When it comes to understanding and troubleshooting a Jeep P0406 Code, it is essential to understand the cause and the solution. The Jeep P0406 Code is a diagnostic trouble code (DTC) triggered when a motor inside the EGR Valve opens the Exhaust Gas Recirculation (EGR) Valve. The Powertrain Control Module (PCM) controls the pulse width modulated motor. The EGR Valve also has an internal three-wire 5-Volt EGR Position Sensor. This internal sensor reports the position of the valve back to the PCM over the EGR Position Sensor Signal circuit. To understand the causes and solutions of this code, it is essential to look at the related service bulletins, such as the 08-008-15. In the following table, we will outline the causes and solutions of the Jeep P0406 Code.
🚨You may be interested in: Jeep P0579 Code
Causes and Solutions of Jeep P0406 Code
| Causes | Solutions |
|---|---|
| EGR Position Signal Circuit Shorted to Voltage | Replace the EGR Position Sensor and clean the wiring. |
| EGR Position Signal Circuit Shorted to the EGR Valve 5-Volt Supply Circuit | Check the wiring and the EGR Valve for any physical defects. |
| Sensor Ground Circuit Open/High Resistance | Replace the EGR Valve and check the circuit for any loose wiring. |
| EGR Valve | Replace the EGR Valve and check the circuit for any loose wiring. |
| Powertrain Control Module (PCM) | Replace the PCM and check the circuit for any loose wiring. |
EGR Position Signal Circuit Shorted to Voltage
The Jeep P0406 Code is triggered when the EGR Position Signal Circuit is shorted to the vehicle’s voltage supply. A damaged wiring harness or a defective EGR Position Sensor can cause this. The EGR Position Sensor should be replaced and the wiring harness cleaned to resolve this issue.
EGR Position Signal Circuit Shorted to the EGR Valve 5-Volt Supply Circuit
When the EGR Position Signal Circuit is shorted to the EGR Valve 5-Volt Supply Circuit, it can cause the Jeep P0406 Code to be triggered. This can be due to a wiring issue or a defective EGR Valve. In this case, the wiring should be checked for any loose connections, and the EGR Valve should be inspected for any physical defects.
⚡️Other article: Jeep P105C Code
Sensor Ground Circuit Open/High Resistance
The Jeep P0406 Code can be triggered if the Sensor Ground Circuit has an open connection or a high resistance. This can be due to a defective EGR Valve or a wiring issue. The EGR Valve should be replaced to resolve this issue, and the wiring should be checked for any loose connections.
EGR Valve
A defective EGR Valve can also trigger the Jeep P0406 Code. The EGR Valve should be replaced to resolve this issue, and the wiring should be checked for any loose connections.
⚡️Other article: Jeep U0420 Code
Powertrain Control Module (PCM)
A defective Powertrain Control Module (PCM) can also cause the Jeep P0406 Code to be triggered. In this case, the PCM should be replaced, and the wiring checked for any loose connections.
👀Look at this: Jeep P1129 Code
Conclusion
In conclusion, understanding the Jeep P0406 Code and its causes and solutions is essential for troubleshooting and resolving the issue. The Jeep P0406 Code is triggered when the EGR Position Signal Circuit is shorted to the vehicle’s voltage supply, the EGR Valve 5-Volt Supply Circuit, the Sensor Ground Circuit has an open connection or a high resistance, or the EGR Valve and Powertrain Control Module (PCM) are defective. The solutions for these issues are replacing the EGR Position Sensor, the EGR Valve, checking the wiring for any loose connections, and replacing the PCM. By following these steps and understanding the Jeep P0406 Code, you will be able to troubleshoot and resolve the issue quickly.